Juniper JN0-661 Exam Questions – Easy Way To Prepare

The easy approach to learning in our Juniper Service Provider Routing and Switching JN0-661 Exam preparation practice test software is especially suited to busy individuals who cannot devote too much time going through much books and manuals. So, stop searching the net for Juniper Service Provider Routing and Switching JN0-661 exam questions which in most cases is unreliable and outdated. Use our Juniper JN0-661 exam which provides timely updates to all course outlines and syllabus.

♥ VALID JN0-661 Exam Questions 2018 ♥

JN0-661 exam questions, JN0-661 PDF dumps; JN0-661 exam dumps:: https://www.dumpsschool.com/JN0-661-exam-dumps.html (133 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Juniper JN0-661 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

You want to ensure that your all-Junos MPLS core network does not decrease the TTL when using ping and traceroute from IP endpoints. Which two configuration parameters satisfy this requirement? (Choose two.)

A. no-decrement-ttl, configured on all routers in the path
B. no-decrement-ttl, configured on the ingress router only
C. no-propagate-ttl, configured on all routers in the path
D. no-propagate-ttl, configured on the ingress router only

Answer: B C

Question: 22

You have configured an MPLS LSP that includes defined hops. For this path, you want the MPLS label to be popped at the egress node.
Which configuration statement meets this requirement?

A. Set protocols rsvp explicit-null, configured on the ingress node
B. Set protocols mpls explicit-null, configured on the egress node
C. Set protocols mpls explicit-null, configured on the ingress node
D. Set protocols rsvp implicit-null, configured on the egress node

Answer: B

Question: 23

Referring to the exhibit, you have configured an L3VPN that connects Site-1 and Site-2 together, but the BGP routes are being hidden on the PE routers. The topology in this scenario is shown below.
Site-1 > PE-1 > P-1 > P-2 > PE-2 > Site-2
Which two acttions would allow communication Site-1 and Site-2? (Choose two.)

A. Disable CSPF on under MPLS on P-1 and P-2.
B. Configure DGP on P-1 and P-2.
C. Enable RSVP for all interfaces on P-1 and P-2.
D. Enable LDP for all interfaces on all routers.

Answer: C, D

Question: 24

A layer 2 circuit (RFC 4447) is established between two PE routers to provide connectivity between two customer sites. Which two statements related to this deployment are true?

A. Kompella encapsulation is used in the data plane communications.
B. LDP must be used for the control plane communications
C. BGP must be used for the control plane communications.
D. Martini encapsulation is used in the data plane communications.

Answer: B, D

Question: 25

Referring to the exhibit, which router will be the RP?

A. R4 for all groups
B. R1 for group 224.1.1.11 and R4 for all other groups
C. R1 for all groups
D. R4 for group 224.1.1.12 and R1 for all other groups

Answer: A

Question: 26

You must ensure that r1’s IPv4 loopback address exists in r3’s inet 0 routing table
Referring to the exhibit, which statement is true?

A. An IPv4 unicast realm can be enabled on each router.
B. A policy can be configured on M to redistribute 172.16.100.1/32 into OSPFv2, which would cause r3 to eventually learn the route and place it into inet0.
C. A RIB group can be configured on r3 to copy that route into inet 0 because 172.16.100.1/32 exists in r3’s inet6.0 table
D. A policy can be configured on r1 to redistribute 172 16 100 1/32 into OSPFv3, which would cause r3 to eventually learn the route and place it into inet 0.

Answer: C

New Updated JN0-661 Exam Questions JN0-661 PDF dumps JN0-661 practice exam dumps: https://www.dumpsschool.com/JN0-661-exam-dumps.html

         

Facebook Comments